Nundah: Standard Residential
Cost: Plan Intel Estimate: $30,000 | DA: A007151638
Lodged: 17/11/2026 | Size: Site area 506m2; existing high-set dwelling with lower-level garage (GFA not listed)
Loc: 23 Bridge Street, Nundah QLD 4012 (Lot 1 on RP34071)
View PlansDA Form
Lodged: 17/11/2026 | Size: Site area 506m2; existing high-set dwelling with lower-level garage (GFA not listed)
Loc: 23 Bridge Street, Nundah QLD 4012 (Lot 1 on RP34071)
View PlansDA Form
OVERVIEW
Full demolition of a substantially altered pre-1947 high-set dwelling house on a 506m2 flat lot at 23 Bridge Street, Nundah, in the Traditional Building Character overlay. Works cover removing the timber-core dwelling with its rendered brick facade, front patio and stairs, masonry lower-level garage and ancillary outbuildings, with no replacement building proposed.CONTACTS
Planner: Steffan HarriesArchitect: Not Listed
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: No new foundations, earthworks or driveway works specified. Works are demolition of the dwelling, including its masonry lower-level supports and garage, and site clearing. The site is largely flat, sloping slightly to the street, with one existing vehicle crossover to Bridge Street. Acid sulfate soils overlay applies.
- Roof & Clad: No new roof or cladding proposed. The existing dwelling being demolished has a re-bricked, rendered and painted front facade, a timber core and a re-roofed section over the front patio. Roof material is not specified.
- Plumbing, Drain & Gas: No new rainwater tanks, gas or drainage works listed. Existing services connections will need disconnecting and capping as part of demolition. The site is in the overland flow flood planning area and the potential/actual acid sulfate soils overlay.
- Elec & Solar: No solar, PV, 3-phase, AC or electrical specs listed. Demolition only. The site is connected to all services, which will need disconnecting before demolition.
- Carpentry, Joinery & Steel: None proposed (demolition only). The existing dwelling has a timber core, an open front patio with new front stairs, and a lower-level garage/enclosure on masonry supports that replaced the original timber stumps.
- Pools & Landscaping: No pool, retaining walls, fencing or landscaping proposed. The site has no significant vegetation and one street tree on the frontage, which needs protecting. Existing ancillary domestic outbuildings are on site.
- Windows & Glazing: None proposed (demolition only). The existing front window is post-war, with no awning or character trims.
- Finishes (Paint/Tile/Floor): None proposed (demolition only). No internal finishes schedule provided.
Fortitude Valley: Standard Commercial
Cost: $436,465.00 | DA: A007151774
Lodged: 17/11/2026 | Size: GFA Not Listed; stair spans 2 levels (Level 1 landing FFL 12.097 to Level 2 Retail FFL 14.490)
Loc: 290 Brunswick Street, Fortitude Valley QLD 4006 (Lot 0 SP175925) – McWhirters Marketplace (the drawings show 270 Brunswick Street)
View PlansDA Form
Lodged: 17/11/2026 | Size: GFA Not Listed; stair spans 2 levels (Level 1 landing FFL 12.097 to Level 2 Retail FFL 14.490)
Loc: 290 Brunswick Street, Fortitude Valley QLD 4006 (Lot 0 SP175925) – McWhirters Marketplace (the drawings show 270 Brunswick Street)
View PlansDA Form
OVERVIEW
Heritage refurbishment and reuse of the disused mid-century escalator at McWhirters Marketplace, turning it into a compliant fire stair to AS1428.1 between the Brunswick St Mall entry landing and Level 2 Retail. Works cover removing the steel treads, new structural steel framing inside the existing escalator truss, timber treads, risers and handrails on stainless steel stanchions, and reinstating the original rubber handrails, aluminium capping, metal sidewalls, kickplates and cladding.CONTACTS
Planner: Extent Heritage Pty Ltd (Applicant's Heritage Advisor, for Body Corporate for McWhirters Retail CTS 34719)Architect: Buchan Holdings Pty Ltd (Buchan)
Builder/Developer: Five 13 Group – trading as OC Studio
TRADE SPECS
- Earthworks, Demo & Concreting: No earthworks, slab or driveway works. New structural steel framing and struts inside the existing escalator truss, to the structural engineer's details. 300mm x 300mm inspection hole in the first floor slab and the plasterboard bulkhead lining. The existing escalator pit (size and construction to be confirmed) is kept. Existing metal treads to be removed (demolition).
- Roof & Clad: No roof works. High-impact escalator cladding with a selected paint finish. Existing escalator cladding and soffit cladding to be reinstated and made good. New edge trim to the bottom of the cladding to match the existing detail. Profiled aluminium capping and internal metal sidewalls to be reinstated. Existing marble wall cladding to stay in place. New escalator soffit lining in flush-set plasterboard with paint finish. Infill stud wall with plasterboard finish. No R-values listed.
- Plumbing, Drain & Gas: None noted. No rainwater tanks, gas or drainage works shown.
- Elec & Solar: None noted. No 3-phase, AC, PV, solar, inverter, smart home or EV charging items in the plans. The works are limited to the escalator-to-stair conversion.
- Carpentry, Joinery & Steel: New timber stair treads and risers to AS1428.1 inside the existing escalator body (15 risers x 159.5mm, 14 goings x 280mm, 1060mm clear width), timber species to be selected by the Architect. New dressed timber handrails on both sides, fixed to new stainless steel stanchions with a concealed top rail and hidden stair stringer. New selected stair nosings. 316 stainless steel tactiles with moulded polymer inserts. Original rubber handrails, profiled aluminium capping, metal sidewalls and kickplates to be reinstated. Existing glass balustrade and timber handrail at Retail Level to be kept. Historical imagery interpretive element near the balustrade and columns (design to be developed).
- Pools & Landscaping: None. The works are internal only, with no pool, retaining walls or landscaping. Temporary construction hoarding (HZ-01), directional signage (vinyl graphics and A-frames), and alternative entry/exit points and travel paths are shown.
- Windows & Glazing: No new glazing. Existing tenancy shopfronts, existing glass balustrade and existing auto-entry doors to remain. The infill stud wall meets the existing glazing frame.
- Finishes (Paint/Tile/Floor): New timber stair treads and risers. Existing terracotta floor tiles at the threshold to be made good, along with the existing Level 2 timber floor and edge trim. Original escalator threshold plates to be reinstated. Existing ceramic wall tiles under the escalator and existing marble wall cladding to be kept and made good. Painted escalator cladding and plasterboard soffit.
Virginia: Standard Commercial
Cost: Plan Intel Estimate: $750,000 | DA: A007151727
Lodged: 17/11/2026 | Size: 250m2, 2 Storeys
Loc: 29 & 29A Telford Street, Virginia QLD 4014 (Lot 1 & 2 on RP 66171)
View PlansDA Form
Lodged: 17/11/2026 | Size: 250m2, 2 Storeys
Loc: 29 & 29A Telford Street, Virginia QLD 4014 (Lot 1 & 2 on RP 66171)
View PlansDA Form
OVERVIEW
This is an approx. 250m² upper-level (mezzanine) ancillary office extension to the existing Laticrete tile adhesive manufacturing facility in Virginia, built above the existing on-grade car park, which becomes undercroft parking. The works include an enclosed ground-floor lunch room, a new lift, amenities, a boardroom, a team/conference room, open-plan offices, labs, a kitchen and a reconfigured car park with an AS2890.6 accessible bay.CONTACTS
Planner: Bartley Burns Certifiers & Town PlannersArchitect: i2C
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: The mezzanine office extension is elevated on columns over the existing on-grade concrete car park, with an enclosed ground-level lunch room. Foundation type is not specified (column footings implied). Minimal earthworks are expected; cut and fill depths are not listed. The site is in the Potential and Actual Acid Sulfate Soils overlay (land at or below 5m AHD). The existing concrete crossover and footpath are retained, and the car park is re-line-marked/reconfigured. Driveway material is not specified.
- Roof & Clad: Roof material and profile are not specified; DA Form 2 ticks 'Other' for external walls, frame, floor and roof covering. Elevations show the existing concrete wall retained, the existing hoods retained, a 7,200mm mezzanine extension on the north (front) facade with screened glazing, a 'roof over' notation, and a ground-level lunch room extension supported on columns. Levels are RL 4.800 (ground) and RL 7.950 (mezzanine). No cladding profiles or insulation R-values are listed.
- Plumbing, Drain & Gas: Existing stormwater pits are retained, with stormwater assessed under the Stormwater Code. The site is in the Flood Overlay (Creek/Waterway Cat 4/5), covered by a Flood Overlay Code Assessment Report by Storm Water Consulting. New amenities include toilets, PWD toilet, kitchen/kitchenette areas and lunch room plumbing. Existing gas bottle storage and fire hydrant/FHR are retained. Existing water and sewer connections are reused. No rainwater tanks are noted.
- Elec & Solar: No solar PV, inverter, 3-phase, A/C, EV charging or smart-home details are shown on the plans. The plans show an existing on-site electrical transformer (retained) and a new passenger lift (3m² at ground and mezzanine levels). The new office, boardroom, lab and lunch room areas will need electrical and data fit-out. The site is already connected to electricity and telecommunications.
- Carpentry, Joinery & Steel: Commercial office fit-out joinery: kitchen and kitchenette joinery on the mezzanine, lunch room joinery, storage rooms, reception/office and boardroom fit-out, and lab benching. Partitioning is needed for multiple offices, a 57m² team/conference room, a 25m² boardroom, meeting rooms and open-plan offices. No staircase/balustrade materials, decking or material brands are specified.
- Pools & Landscaping: No pool. Outdoor works are limited to the existing footpath garden along Telford Street (retained) and a reconfigured on-site car park with increased spaces and an AS2890.6-compliant accessible space. Existing parking becomes undercroft/covered parking under the extension. The existing roofed outdoor staff recreation/breakout area is replaced by an enclosed lunch room. The existing crossover on Telford Street is retained. No retaining walls or new fencing are noted.
- Windows & Glazing: Elevations show screened glazing to the new mezzanine extension on the north facade, new proposed glazing to the ground-level lunch room extension, and existing glazing retained. Frame materials, glass types, louvres and skylights are not specified.
- Finishes (Paint/Tile/Floor): Not specified; DA Form 2 ticks 'Other' for floor. Internal floor coverings and feature wall finishes are not detailed on the plans.
Brighton: Standard Residential
Cost: Plan Intel Estimate: $85,000 | DA: A007151614
Lodged: 16/11/2026 | Size: 340.6m2 total (315.4m2 existing + 25.2m2 proposed), 2 Storeys
Loc: 33 Stubbs Street, Brighton QLD 4017 (Lot 3 on SP235454)
View PlansDA Form
Lodged: 16/11/2026 | Size: 340.6m2 total (315.4m2 existing + 25.2m2 proposed), 2 Storeys
Loc: 33 Stubbs Street, Brighton QLD 4017 (Lot 3 on SP235454)
View PlansDA Form
OVERVIEW
Ground-floor alterations and additions to an existing two-storey, four-bedroom brick dwelling at Brighton, adding about 25.2m2 of living room and rear patio/deck extension on a new engineered slab under a Colorbond roof at a 15-degree pitch, to match the existing. Works include new walls to enclose the media room, removal of existing windows, doors and a pergola, new powder-coated aluminium sliding windows and doors, rendered brick piers with SHS posts, and removal of the rear yard gazebo. The upper level is not changed.CONTACTS
Planner: Danya Cook Town PlanningArchitect: Moreton Bay Designs
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: Concrete slab-on-ground extension; footings, slab and slab join as per the engineer's design (AS2870). The slab is topped to match the existing internal floor height, with a 75mm step to the patio. Minimum 0.2mm polythene vapour barrier and anti-termite treatment (AS3660.1, Biflex or similar). Remove topsoil to at least 200mm; clean fill compacted in layers no thicker than 300mm, with equal cut and fill and batters of up to 1 in 2 cut and 1 in 4 fill. The site is flat. 350mm brick piers. No new driveway works (existing crossover kept).
- Roof & Clad: New Colorbond (steel) roof at a 15-degree pitch to match the existing, on roof trusses at 900 centres. Ceiling height 2750mm, wall height 2400mm. Walls are brick veneer on a timber frame; brick walls and 350mm piers are rendered to match the existing (2-coat sand-finish render for painting). Insulation: reflective insulation with a 25mm airspace; enclosed sub-floor and roof space R0.45; internal heated water piping R0.2.
- Plumbing, Drain & Gas: Minimum 100x75 downpipes, each draining no more than 50m2 of roof, into stormwater pipes at a minimum 1% grade. Roof water disperses to Stubbs Street kerb and channel through 100mm stormwater drainage. Finished ground level must be at least 75mm below the damp course, falling away from the house at 1:20. Sewer and stormwater line positions to be confirmed on site. Heated water pipes to be insulated. No rainwater tanks or gas extensions noted.
- Elec & Solar: No solar PV, inverter, 3-phase power, A/C, EV charging, smart home or security wiring noted. Electrical schedule: 4 x CAT5 with TV points, 1 x ceiling fan, 2 x LED downlights, 1 x double remote-head light, 5 x double power points. The site has an overhead electricity supply.
- Carpentry, Joinery & Steel: No high-value joinery shown (no cellar, bar, butler's pantry or chutes). Scope: new timber-framed walls to enclose the media room (AS1684); 2 x 720 cavity sliding doors; existing opening square-set and made good; existing doors and windows removed and walls made good. External door frames are 110x40 double-rebated timber with a 130x40 weathered threshold. New roof trusses at 900 centres; bulkheads per drawings. Rear deck/patio is on a slab with 350mm brick piers and SHS posts; no balustrade or decking material specified, and no internal staircases.
- Pools & Landscaping: No pool. A new rear patio/deck extension opens off the living room. The freestanding rear gazebo and the existing pergola are removed to open up the backyard. Existing lawn and garden areas are kept. No new retaining walls or fencing are shown, though the spec says any retaining walls need Bitkote waterproofing. Ground is graded at 1:20 away from the house.
- Windows & Glazing: Powder-coated aluminium window frames (colour chosen by owner), flyscreens on all windows, clear glass generally with obscure glass to bathrooms, installed to manufacturer specs. New units: 1346 OXXO sliding window, 1326 OXXO sliding window, and a 2427 XXO sliding door to the patio. Existing windows and doors are removed. Any roof lights are to be weather-sealed.
- Finishes (Paint/Tile/Floor): No specific finishes schedule. The general spec allows for carpet with underlay, tiles with trims, and sanded and polished timber boards (2 coats of sealer) to nominated areas. Internal walls are hardwall plaster, ceilings are minimum 8mm plasterboard with recessed edges and cornices, and openings are square set. No feature walls noted.
St Lucia: Premium Residential
Cost: Plan Intel Estimate: $9,500,000 | DA: A007151698
Lodged: 16/11/2026 | Size: GFA not listed (site cover 783m2), 5 Storeys
Loc: 68-74 Warren Street, St Lucia QLD 4067 (Lots 45, 46 & 47 on RP23318)
View PlansDA Form
Lodged: 16/11/2026 | Size: GFA not listed (site cover 783m2), 5 Storeys
Loc: 68-74 Warren Street, St Lucia QLD 4067 (Lots 45, 46 & 47 on RP23318)
View PlansDA Form
OVERVIEW
This is a new 5-storey apartment building with 11 self-contained units of 5 to 7 bedrooms each (64 bedrooms in total), aimed at student renters near UQ, on a sloping 1,215m2 flood-affected site in St Lucia. The build includes an undercroft carpark for 26 cars with a sprinkler pump room and lift, relocation of a sewer main with new manholes, retaining walls of 1-2.2m, a 153m2 rooftop deck with BBQs and planters, and facades of stacked stone, pipe clay and bluegum cladding with timber-look screening.CONTACTS
Planner: MeconeArchitect: Kris Kowalski Architects
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: Cut and fill across a site that falls about 10% (10m to 4.81m AHD) to form an undercroft or semi-basement concrete slab at RL 6.3m AHD, clear of the relocated sewer. Perimeter retaining walls range from 2.2m (south) to 1m (north). Floors are concrete and the frame is steel. There is a new 6.5m-wide concrete crossover and driveway with 1:20, 1:8 and 1:5 ramps and a speed bump, plus 1:14 pedestrian ramps. Acid sulfate soils overlay applies. The driveway material is not specified.
- Roof & Clad: Skillion roof form with aluminium roof covering (DA Form 2), steel frame and concrete floors. External walls are brick veneer, stone/concrete and fibre cement. The finishes legend lists Pipe Clay cladding (Dulux A129 Clay Pipe), Bluegum colour, Monument colour, timber-look screening, feature screening, stacked stone cladding and an entry arbour. No R-values or specific cladding profiles are listed.
- Plumbing, Drain & Gas: Sewer gravity main LS177284 is to be relocated to invert levels of 5.40m AHD (south) and 4.84m AHD (north), with new sewer manholes reached by 1m pathways. Water connects to the Warren Street main via a new master meter, and a fire booster and sprinkler pump room are required. Gas connection to the medium-pressure main in Warren Street will be confirmed at detailed design. Roof runoff is collected and piped to stormwater at the Warren Street frontage, and no on-site detention is proposed. The refuse room includes bin wash facilities. Flood immunity: habitable floor level 9.45m AHD, basement entry 6.3m AHD. No rainwater tanks noted.
- Elec & Solar: No solar PV, inverter, 3-phase, AC, EV charging or smart-home wiring is noted. Electricity connects to the supply in Warren Street, with an MSB (main switchboard) next to the bin store. The building has a lift, a sprinkler pump room and fire booster, and outdoor lighting under the Outdoor lighting code. Telecommunications connect to existing Warren Street infrastructure.
- Carpentry, Joinery & Steel: 11 kitchens and 11 internal laundries across the units, with 64 bedrooms that will need wardrobe joinery. No cellar, bar, butler's pantry or chutes are shown. There are glass balustrades to the balconies, fixed and adjustable timber-look and feature screening, and an entry arbour. Access is by a lift and an internal fire stair. The rooftop deck has BBQs and a WC.
- Pools & Landscaping: No pool. Deep planting areas of 152.9m2 (12.6% of the site): 39m2 at the frontage and 120m2 at the rear, with subtropical trees (Acmena hemilampra, Buckinghamia celsissima, Delonix regia, Elaeocarpus eumundii). Podium planters on the north and south facades, and a 1.6m-wide perimeter planter around the 153m2 rooftop deck with BBQs, WC and arbour. An acoustic fence runs along the boundary. Retaining walls range from 2.2m (south) to 1m (north). The street tree is to be replaced, the verge upgraded and existing rear vegetation removed (landscape design by Dunn & Moran).
- Windows & Glazing: Large windows and glass balconies (balustrades) on all facades. Fixed privacy screens are placed at intervals on the southern facade, and adjustable screening adds articulation. No frame material, glass type, louvres or skylights are specified.
- Finishes (Paint/Tile/Floor): Concrete floor structure. No internal floor coverings or feature wall finishes are specified, as no finishes schedule was provided.
Hawthorne: Premium Residential
Cost: Plan Intel Estimate: $1,650,000 | DA: A007151724
Lodged: 17/11/2026 | Size: 552m2 total floor area (Ground 46m², L1 184m², L2 195m², L3 127m²), 3 Storeys (4th technical storey at garage level)
Loc: 72 Coventry Street, Hawthorne QLD 4171 (Lot 378 on RP13158)
View PlansDA Form
Lodged: 17/11/2026 | Size: 552m2 total floor area (Ground 46m², L1 184m², L2 195m², L3 127m²), 3 Storeys (4th technical storey at garage level)
Loc: 72 Coventry Street, Hawthorne QLD 4171 (Lot 378 on RP13158)
View PlansDA Form
OVERVIEW
This is a major renovation and extension of a split-level home at 72 Coventry Street, Hawthorne, giving about 552m² of floor area over 3 storeys. It includes a new Level 3 master suite, a rear extension, and a new Linea weatherboard and stone facade under a hipped Colorbond Trimdek roof. High-value features include a wine cellar, a wine store, a bar and rumpus, a mud room, a lift, a glass-balustraded deck with BBQ, a walk-in pantry, skylights and an EV charger, with the existing pool retained.CONTACTS
Planner: Rivo Town PlanningArchitect: DZ Architects
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: The existing excavated garage level (cut into a slope of about 3.7m) is retained, with a new mud room and wine store fitted out inside it. Walls are 190 core-filled blockwork, rendered and painted, built to the structural engineer's details; there are also rendered planters and a breeze block screen wall. Foundations, slabs and earthworks are 'refer to structural engineer' and are not specified. The existing aggregate concrete driveway and crossover are retained.
- Roof & Clad: Roof: Trimdek metal roof sheeting (MRS1) in Colorbond Dover White, hipped forms at 10° pitch with ridge capping. Eaves are 450-500mm. Gutters are 250/150 Colorbond half-round eaves gutters in Dover White. Walls: Linea FC weatherboard painted white (CLD1); texture-rendered painted FC (CLD2); feature stone cladding and piers (STN1); 190 core-filled blockwork, rendered and painted (BW1); breezeblock feature screening (BRZ1); powdercoated aluminium timber-look battens (BATT1) and aluminium screening (BATT2). Horizontal sun hoods are shown. No insulation R-values are listed.
- Plumbing, Drain & Gas: Downpipes are 100mm diameter Colorbond in Dover White, draining from 250/150 half-round eaves gutters. The existing gas meter is retained. Existing sewer lines run through the site (shown on the site plan). A new wine cellar, laundry, ensuite, two new bathrooms and a WC are planned, plus a BBQ area on the Level 1 deck. No rainwater tank is noted.
- Elec & Solar: The plans show a 'Solar Box' on the Level 1 south side, but no PV system size or inverter is specified. Other items shown: a 'Rapid Pole' EV charger in the garage, an electrical meter box and data board, an A/C condenser unit, and a lift serving all levels. 3-phase power, smart home wiring and security systems are not noted.
- Carpentry, Joinery & Steel: Custom joinery is shown for:
- Level 1: bar and rumpus, wine cellar (1.72m²) and kitchen with walk-in pantry, dishwasher and open shelving
- Garage level: wine store (3.18m²) and mud room (4.25m²) with bench seat and a 900H bench with cupboards above and below
- Laundry
- Walk-in wardrobes to all bedrooms, plus a master walk-in wardrobe with make-up station
- Built-in study desks, a library/open study area and feature art walls
- Level 3: 1200H partition wall
Also included: new internal stairs, a lift, a 1020H top-mounted glass balustrade with handrail (BAL1), and timber-look aluminium battens. Decks: a 30m² front deck, a 22m² balcony and a 19.64m² rear deck (decking material not specified). - Pools & Landscaping: The existing in-ground pool and pool terrace are retained with no works. The landscaped front garden, aggregate driveway and crossover are also retained. New works: an artificial turf (astro turf) courtyard on Level 1; a rendered front planter; and a breeze block screen wall set 0.6m from the south boundary beside the BBQ deck, on a blockwall with breeze blocks on top. Existing rendered blockwork boundary walls and the sliding gate are retained. The rear yard gets new turf, and the existing deep planting along the western boundary is kept.
- Windows & Glazing: Windows and doors are powdercoated aluminium-framed glass in Dover White (AFW). Skylights are shown on Levels 2 and 3. Existing louvres are reused on Level 2, and horizontal sun hoods sit over the glazing. Balustrades are 1020H glass with a top-mounted handrail. The garage gets a new panel sectional door. No glass types (e.g. Low-E, double-glazed, tinted) are specified.
- Finishes (Paint/Tile/Floor): Internal floor coverings are not specified on the plans. Feature art walls are shown in the living area, Level 2 hallway and study areas. The Level 1 courtyard has artificial turf.
Upper Mount Gravatt: Premium Residential
Cost: Plan Intel Estimate: $35,000,000 | DA: A007151572
Lodged: 16/11/2026 | Size: 7,658m2, 8 Storeys (plus 2 basement levels)
Loc: 35-41 Mascar Street, Upper Mount Gravatt QLD 4122 (Lots 37 & 38 on RP70001 & Lot 49 on RP111693)
View PlansDA Form
Lodged: 16/11/2026 | Size: 7,658m2, 8 Storeys (plus 2 basement levels)
Loc: 35-41 Mascar Street, Upper Mount Gravatt QLD 4122 (Lots 37 & 38 on RP70001 & Lot 49 on RP111693)
View PlansDA Form
OVERVIEW
New 8-storey, 78-unit apartment building (2 and 3-bed units) on a 2,127m² corner site, with two basement levels plus ground-level parking for 152 cars, a gatehouse entry and a 467m² landscaped rooftop communal area with a children's playground, BBQ/dining zones, a bar bench and open pergolas. High-value features include butler's pantries in the units, a refuse chute to a ground-floor bin room, an underground stormwater detention tank, painted and rendered blockwork façades with aluminium screens and sunhoods, and frameless glass balustrades.CONTACTS
Planner: Town Planning Alliance Pty LtdArchitect: VSA Design
Builder/Developer: To Be Appointed
TRADE SPECS
- Earthworks, Demo & Concreting: Bulk excavation for two basement levels: ground RL 58.25, B1 RL 55.25, B2 RL 52.25, roughly 6m below ground. Basement retaining walls to engineer's details, concrete ramps (1 in 4 to 1 in 20) and a reinforced concrete multi-storey frame. Site falls about 2m from SW to NE (3% grade). Basement no more than 1m above natural ground. Demolition of 3 existing dwellings. Two Type B2 concrete crossovers to BCC standard (6.5m to Mascar St, 6.2m to Everett St). 1.8m concrete footpaths on both frontages. Existing crossovers to be removed and verge reinstated. Driveway finish not specified.
- Roof & Clad: Flat roof used as a trafficable rooftop terrace with communal and private open space, open pergolas, planter boxes and a lift overrun; roof sheeting material and profile not specified. External walls are painted and rendered blockwork with aluminium batten and vertical screens, louvre screening, sunhoods, and recessed balconies and projecting bays. Floor-to-floor heights are 3.2m, with 2.7m minimum ceilings. No R-values listed.
- Plumbing, Drain & Gas: New pit and pipe stormwater network to a 31.45m³ underground detention tank in Basement 1, discharging via a new line to the Mascar St gully pit. Roofwater first-flush diverters and landscape swales. External catchment flows diverted along the site. New water connection and meter off the 100mm main in Everett St. New sewer connection to the Everett St main. Hydrant and sprinkler pump room and booster cabinet. APA gas connection available if required. Reticulated irrigation with stormwater harvesting. Rooftop planter drainage and waterproofing. Refuse chute to the ground-floor bin room.
- Elec & Solar: No solar PV, inverter, EV charging or smart home wiring noted. Padmount transformer (if required) at the SE corner. Electrical risers and mechanical plant rooms. Air-conditioning condensers on each balcony. Exhaust and fresh air risers to the basements. Supply from existing overhead and underground infrastructure in Mascar and Everett Streets. Outdoor and car park lighting to AS 4282 and Category P3 entry lighting.
- Carpentry, Joinery & Steel: 78 units of kitchen joinery, many with butler's pantries. Built-in wardrobes and walk-in robes, linen cupboards, laundries and study nooks, plus ensuite and bathroom vanities. Rooftop bar benches and pergolas. Refuse chute hoppers on each level. Concrete fire stairs (2), with no feature internal staircases. Semi-frameless glass balustrades to balconies. No cellar or decking specified, and no material or brand specs given.
- Pools & Landscaping: No pool. 229m² of deep planting (10.8% of the site) in three zones along both frontages and the western boundary, with Waterhousea floribunda, Randia fitzalanii, Elaeocarpus eumundii and Tristaniopsis 'Luscious' (45L stock). Syzygium 'Straight & Narrow' buffer planting along the southern boundary. 1.8m high acoustic fence on the southern and western boundaries. Gatehouse entry with low walls. New street trees (Buckinghamia celsissima to Mascar St, Cupaniopsis anacardioides to Everett St). 2 existing Leopard Tree street trees removed. 467m² rooftop communal area with synthetic turf lawn, children's playground, BBQ/dining zones, bar benches, open pergolas, a PWD toilet, perimeter planters (1m deep) and a maintenance track.
- Windows & Glazing: Aluminium-framed windows and aluminium-framed sliding doors to balconies. Semi-frameless glass balustrades. Fixed vertical aluminium screens and full-height louvre screens. High-set windows only on the western façade for privacy. Sunhoods over openings. Any reflective glass to have no more than 20% light reflectivity. No skylights or double glazing noted.
- Finishes (Paint/Tile/Floor): Internal floor coverings and finishes schedule not provided. Synthetic turf on the rooftop multi-purpose area and play mound. Paved rooftop terraces and courtyard. Concrete basement and car park floors.
